AOpen DE7200 Series Provozní pokyny Strana 97
- Strana / 167
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
MAINTENANCE
31 Dec 13 5-35
DE-7200VFDCentrifuge
ALARM AND FAULT MESSAGES
Cause Corrective Action
F9099 - Centrifuge Sensor I/O Cable Has Been Removed, Reconnect I/O Cable to Run
Centrifuge
Sensor cable is disconnected from
control cabinet receptacle
Plug in connector at upper left of cabinet, and then
re-start centrifuge.
VFD ALARM AND FAULT CROSS REFERENCES
In addition to alarm and fault messages that may appear on the operator control panel, in case of
equipment malfunction alarm and fault numbers may appear directly on the VFD screens. An
alarm is a condition that, if neglected, may stop the drive. A fault is a condition that stops the
drive.
The following tables list these alarm and fault numbers and the corresponding text. This
information is useful for operators and Derrick personnel to diagnose equipment malfunctions. To
expedite troubleshooting, record the code number before calling for service and then relay this
information to the service engineer.
ALARM CROSS REFERENCE
No.
Alarm
No.
Alarm
No.
Alarm
1 Precharge Active 14 Load Loss 27 Speed Ref Cflct
2 UnderVoltage 15 Ground Warn 28 Ixo Vlt Rang
3 Power Loss 17 Dig In ConflictA 29 Sleep Config
4 Start At PowerUp 18 Dig In ConflictB 30 TB Man Ref Cflct
5 Analog In Loss 19 Dig In ConflictC 31 PTC Conflict
6 IntDBRes OvrHeat 20 BiPolar Conflict 32 Brake Slipped
8 Drive OL Level 1 21 Motor Type Cflct 33 AdjVoltRef Cflct
9 Drive OL Level 1 22 NP Hz Conflict 34 Home Not Set
10 Decel Inhibt 23 MaxFreq Conflict 49 Torq Prove Cflct
11 Waking 24 VHz Neg Slope 50 Prof Step Cflct
12 Motor Thermistor 25 IR Volts Range 52 PI Config Cflct
13 In Phase Loss 26 FluxAmpsRef Rang
- DE-7200 Centrifuge 1
- CONTENTS 5
- Section 6
- CONTENTS 7
- SECTION 1 - INTRODUCTION 9
- EQUIPMENT USE 10
- DESCRIPTION 10
- Rotating Assembly 11
- Drive Motors 12
- Control Cabinet 12
- Case and Base 13
- Vibration Switch 13
- MECHANICAL OPERATION 14
- CONTROL SYSTEM 15
- PRODUCT SUPPORT 16
- CONTACT INFORMATION 16
- SECTION 2 - SAFETY 17
- Equipment Handling 18
- Maintenance 19
- Storage 19
- MSDS’S (CONT’D) 20
- SECTION 3 - INSTALLATION 21
- STORAGE 22
- Rotating Assembly and Motors 22
- INSTALLATION SEQUENCE 23
- EQUIPMENT HANDLING 24
- EQUIPMENT HANDLING (CONT’D) 26
- Liquid Discharge 29
- Solid Discharge Chute 29
- EQUIPMENT LEVELING 29
- FEED AND FLUSH CONNECTIONS 31
- COMPRESSED AIR 33
- FEED PUMP 33
- ELECTRIC POWER CONNECTIONS 33
- Connection Options 33
- POLARITY TEST 36
- SENSOR CONNECTIONS 37
- MACHINE STARTUP 38
- GENERAL 39
- SOFTWARE VERSION 39
- OPERATING SAFETY 39
- Purge System Bypass 40
- INITIAL STARTUP 41
- INITIAL STARTUP (CONT’D) 42
- OPERATING INSTRUCTIONS 43
- NORMAL STARTUP 44
- COLD CLIMATE STARTUP 45
- OPERATION 45
- Bowl Speed 47
- Conveyor Differential Speed 47
- Pond Depth 47
- Pond Depth (Cont’d) 48
- BEARING TEMPERATURES 50
- MOTOR TORQUE TREND 50
- SYSTEM DIAGNOSTICS 51
- PERFORMANCE STATUS 51
- ALARM AND FAULT MESSAGES 52
- VFD STATUS 53
- VFD STATUS (CONT’D) 54
- PUMP VFD FAULT STATUS 54
- VFD TEMPERATURE TRENDS 55
- VFD FAULT RESET 55
- VFD FAULT RESET (CONT’D) 56
- SETUP SCREEN 56
- PUMP SETUP SCREEN 57
- CLEAN OUT 57
- CLEAN OUT (CONT’D) 58
- Automatic Cleanout 58
- Manual Cleanout 58
- NORMAL SHUTDOWN 59
- AUTOMATIC SHUTDOWN 59
- Excessive Vibration 59
- Main Bearing Temperatures 59
- Excessive Bowl Speed 60
- Conveyor Clutch Trip 60
- EMERGENCY SHUTDOWN 61
- Electric Power Shutdown 61
- Mechanical Shutdown 61
- SECTION 5 - MAINTENANCE 63
- PREVENTIVE MAINTENANCE 64
- LUBRICATION CHART 65
- GEARBOX OIL LEVEL CHECK 65
- GEARBOX OIL CHANGE 66
- DRIVE BELT REPLACEMENT 67
- PURGE SYSTEM 69
- Bypassing Purge System 69
- Initial Purge Time Setting 70
- Leakage Compensation Test 71
- Rotating Assembly Removal 73
- Cleaning and Inspection 75
- Installation 76
- RECOMMENDED SPARE PARTS 77
- TROUBLESHOOTING 79
- Troubleshooting Procedure 79
- TROUBLESHOOTING (CONT’D) 80
- Troubleshooting Chart 80
- CONTROL COMPONENT INDICATORS 98
- MAINTENANCE 100
- DE-7200VFDCentrifuge 103
- CONTROL ENCLOSURE ASSEMBLY 141
- DE-7200 EX-PROOF 460/480/60/3 141
- 16472-00-002 141
- DE-7200 EX-PROOF 380/400/3 143
- 16472-00-003 143
- DE-7200 EX-PROOF 575/600/60/3 145
- 16472-00-004 145
- DE-7200 460/480/60/3 147
- 16472-00-005 147
- PURPOSE 149
- DE-7200VFDCentrifuge 150
- INSTALLATION 156
- HMI Server Installation 156
- Electric Power Connections 156
- Ethernet Connections 157
- Appendix A-HMIServerSystem 158
- OPERATING HMI SERVER 159
- Startup and Shutdown 159
- Operation 159
- Operation (Cont’d) 160
- REFERENCE DRAWINGS 164
Související produkty a manuály pro Barebones pro PC / pracovní stanice AOpen DE7200 Series
(11 stránky)
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce